transformers july 2013 pulse transformers for lan interface alt series ALT3232M alt4532m
(2/9) 001-01 / 20130722 / trans_alt_en.fm transformers reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/9) 001-01 / 20130722 / trans_alt_en.fm ? all specifications are subject to change without notice. transformers pulse transformers for lan interface features the alt3232 series contains wound chip type pulse transformers developed for lans. compatible with 10base-t, 100base-tx, and 1000base-t. high-quality product that uses auto winding. conforms to the rohs directive. application lan interfaces of various devices including net work devices, communication equipment, digital consumer electronics, etc. part number construction operating temperature range, package quantity, product weight operating temperature range includes self-temperature rise. the storage temperature range is for after the circuit board is mounted. overview of the alt series alt 3232 m 151 t 001 series name lwh dimensions product internal code inductance packaging style internal code (mm) (h min.) at 100khz/dc bias=8ma 3232 3.23.22.8 m 151 150 t taping 4532 4.53.22.8 ty p e temperature range package quantity individual weight operating temperature storage temperature c c pieces/reel mg ALT3232M C40 to +85 C40 to +85 2,000 120 alt4532m-201 C40 to +85 C40 to +85 2,000 160 alt4532m-171 C40 to +85 C40 to +85 2,000 110 product compatible with rohs directive halogen-free compatible with lead-free solders rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://www.t dk.co.jp/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/9) 001-01 / 20130722 / trans_alt_en.fm ? all specifications are subject to change without notice. transformers overview of the alt series recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 10 to 30s 245c 5s max. natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/9) 001-01 / 20130722 / trans_alt_en.fm ? all specifications are subject to change without notice. transformers alt series ALT3232M type shape & dimensions recommended land pattern circuit diagram dimensions in mm 3.20.25 2.9max. 3.20.25 1 2 3 6 5 4 dimensions in mm 0.90.9 1.35 0.65 0.7 0.41 0.41 0.41 0.85 2 3 1 5 4 6
(6/9) 001-01 / 20130722 / trans_alt_en.fm ? all specifications are subject to change without notice. transformers alt series y ALT3232M type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. insertion loss vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. turns ratio # : " ! inductance (h)min. [dc bias 8ma, 100khz] - insertion loss (db)max. [0.1 to 100mhz] - " ! inter-winding stray capacitance (pf)max. [100khz] part no. 1ct : 1ct 150 2.5 25 ALT3232M-151-t001 measurement item product no. manufacturer inductance 4284a agilent technologies insertion loss 8753d agilent technologies inter-winding stray capacitance 4284a agilent technologies product no. manufacturer 8753d agilent technologies insertion loss ( db ) frequency ( mhz ) 0 1.0 2.0 3.0 4.0 0.1 1 10 100
(7/9) 001-01 / 20130722 / trans_alt_en.fm ? all specifications are subject to change without notice. transformers alt series alt4532m type shape & dimensions recommended land pattern circuit diagram dimensions in mm 3.20.2 t 4.50.2 1 2 3 6 5 4 t 2.2max. 2.9max. dimensions in mm 1.39 1.39 1.32 0.65 0.72 0.41 0.41 0.5 1.0 2 3 1 5 4 6
(8/9) 001-01 / 20130722 / trans_alt_en.fm ? all specifications are subject to change without notice. transformers alt series y alt4532m type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. insertion loss vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. turns ratio # : " ! inductance (h)min. [dc bias 8ma, 100khz] - " - ! insertion loss (db)max. [0.1 to 100mhz] - " ! inter-winding stray capacitance (pf)max. [100khz] part no. 1ct : 1ct 170 2.5 35 alt4532m-171-t001 1ct : 1ct 200 1.5 35 alt4532m-201-t001 measurement item product no. manufacturer inductance 4284a agilent technologies insertion loss 8753d agilent technologies inter-winding stray capacitance 4284a agilent technologies product no. manufacturer 8753d agilent technologies insertion loss ( db ) frequency ( mhz ) 0 1.0 2.0 3.0 4.0 0.1 1 10 100 171 201
(9/9) 001-01 / 20130722 / trans_alt_en.fm ? all specifications are subject to change without notice. transformers alt series packaging style reel dimensions tape dimensions ty p e a w1 w2 n e alt3532m ?3302 13.50.5 17.51 1001 2 typ. alt4532m ?3302 13.50.5 17.51 1001 2 typ. dimensions in mm ty p e a b ?d0 e f p0 p1 p2 w k t alt3532m 3.550.1 3.550.1 1.5+0.1/0 1.750.1 5.50.1 4.00.1 8.00.1 2.00.1 12.00.2 3.00.1 0.30.05 alt4532m 3.60.1 4.90.1 1.5+0.1/0 1.750.1 5.50.05 4.00.1 8.00.1 2.00.1 12.00.2 3.25max. 0.30.05 ?13.0 0.2 ?21.0 0.8 n e 2.0 0.5 a dimensions in mm 1.0 w2 w1 b fe w p0 p2 p1 a ?d0 t k dimensions in mm 160min. taping 440min. drawing direction 500 to 560min.
|
